Measurement of coating thickness on the applied substrate

Standards

• ASTM D 6132, ISO 2808 - Ultrasonic Technique.Measuring range - 0.5 to 150 mils
• ASTM E 376 - Magnetic adhesion property through eddy currents

Significance:

• Ferrous models will measure all non-ferromagnetic coatings on steel and iron.
• Non-Ferrous models will measure all non-conductive, non-Non-Ferrous substrates.

This simple to use gauge is ideal for evaluating the resistance of a coating to impact (elongation, cracking or peeling)

Standards

• ASTM G-14,D2794,IS, DIN,ISO
• Specimen Size: 0.025 in. or 0.63mm
• Indentor size: 0.5 in. or 12.7mm
• Weight of Tub: 1.361 Kg.
• Drop range: 0.61 to 1.22m [2 to 4 ft.]
• Specimen Size: 0.025 in. or 0.63mm

If no cracks are evident, repeat the procedure at a greater height, increasing 1 in. (25mm) at a time.

Simple & effective technique to evaluate the hardness and resistance to scratching of coatings

Standards

• ASTM D 3363
• The Pencil Hardness Tester is a simple and affective technique to evaluate the hardness and resistance to scratching of coatings .
• The test method allows the used of pencils which have a known hardness grade to be moved over the surface to be tested at a fixed angle and pressure .

Allows the use of pencils which have a known hardness grade to be moved over the surface to be tested at a fixed angle and pressure.

Also known as conical mandrel testis a mechanical tester used to determine the effects of bending on the elasticity, adhesion and elongation properties of cured coatings on sheet metal

Standards

• ASTM D 522
• BS 3900-E11
• SO 6860

The Cross Hatch Cutter allows an assessment to be made of the adhesion resistance of coatings to separation from substrates when a right-angled lattice pattern is cut into the coating and penetrates through to the substrate.

Stormer viscometers-(ASTM D 562)

• ASTM D 3359
• The 1mm Cutter is suitable for coatings under 60 microns.
• The 2mm Cutter is suitable for coatings over 60 microns.
• Multiple coatings can be tested for the assessment of the resistance to separation of individual layers of the coating from each other.

Defined as resistance to indentation or scratching

Standards

• ASTM D 2197
• BF 3900
• D2197
• ISO 1518
• RANGE 100g TO 10kg

• The scratching needle is a harderned steel hemispherical tip of 1 mm dia.
• Clam the panel on the DC circuit panel
• Place weight on the holder above the needle
• Start the motor to make a scratch on the coting
• Observed the scratch for penetration upto the substrate
• Failure of the coting is the indicated by deflaction in the current needle due to completion of the circuit
• A Voltmeter indicates the contact, when the needle touches the base metal. The automatic systems disengage the needle from the panel when returning to home
• position.Failure of the coating is indicated by deflection in the current needle due to completion of circuit.

Measures the hardness of the surface of the coating.

Standards

• ASTM D 2240 ASTM D 2240 Fiberglass,Aluminum,Soft Metals,Plastics,Painted Surface
• Take the measurement at last 12 mm form the edge of the material
• the material must be at last 6 mm thick
• Required pressure must be applied for 15 seconds
• This force should be max 4.55 kg for a type D durometer
• Meaning of a durometer reading
  no indent sign :100
  If indentation upto:2.5 mm :0
• Measurements taken at 12mm from the edge of material
• Material must be at least 6mm thick.

The Holiday Dete ctor is a DC Holiday Tester that tests and detects pinholes and flaws in insulated coatings on conductive substrates.

Standards

• ASTM D 4787
• ASTM G 62
• ISO 2746
• BS 1344-11

Significance

• Pinholes in coatings invisible to naked eyes./li>
• Detector counts pinholes and sounds alarm.
• Allows instant repair of pinholes.
• Especially suitable for large diameters and enables reliable testing of the complete tube in one or two operations only.

designed to perform accelerated wear tests on a variety of specimens.

Standards

• ASTM D 4060

Significance

• Wheels shall be 12.7mm thick and have an external diameter of 51.9mm and in no case less than 44.4mm.
• Wheels CS-17,10 H-10, 18, 22 & OTHERS

measures the adhesion bond strength of applied coatings with ease, and precision.

Standards

• ASTM D 4541
• ISO 4624
• The adhesion is measured by the tensile pull on a Dolly glued to the coating surface.
• The force is applied through the centre of the Dolly by a hydraulically loaded pin.
• This ensures an exactly central point-loading of the force.

also known as auniversal tester,materials testing machineormaterials test frame, is used totestthetensile strength and compressive ,Peel , flexural strength of materials.

Standards

• ASTM /IS /DIN/ISO & OTHERS
• Tensile strength
• Elongation
• Peel test
• Compressive test
• Bond test
• Flexural test
• Tear test
• Shear test
• Joint bend test